S10 gas tank swap.

Feb 29, 2004 · hell we swapped my bed to another guys truck and his step side to my truck within 3 hours. its actually very simple. take off the rear bumper. take out the tail lights. remove the tail light harness from the bed. remove the ground strap from the frame that connects to the filler neck. remove filler neck from the gas tank along with the rubber ... Do a search for blazer gas tank swap on here, capt has done one with pics. Logged. #1: The easiest and most obvious solution to any problem is 99% of the time correct. #2: There is no such thing as impossible, it just takes longer. 74 k10, 77k10 Tom.1st gen Blazers/Jimmys had either 13.2 or 20 tanks. I don't know the 2 or 4 door differences. 1 gen s10/Sonomas have either 13 or 20 gallon tanks. Either tank could be in short beds, long beds, regular cabs, ex cabs. ALL 2nd gen trucks have 18.5 gallon tanks.Messages: 90. Location: Black mtn, NC. I have a few questions on putting my body on the s-10 frame. 1) when I put the body on the frame with blocks of 4x4 ( the gas tank in the rails of the s-10 on the drivers side hits the back of the cab) Do I trim the body so it fits lower? 2) the bed sits on the frame at the tail gate end (which is as low ...Basically I removed the old fuel tank, cut out the rear frame crossmember and welded in new braces to support the blazer tank, cut out both upper mounts on the frame and lower shock mounts on the axle, moved rear brake line mount in front of the axle, bought new leaf spring plates which also have shock mounts on them. So seeing that I

A plug and play harness will completely wreck a $1500 budget and will leave less than $2000 on the $3k swap. If I were doing either of those I'd be modifying a factory harness. A $3k budget will require junkyard parts for most of what you change and reusing as much as you can from the donor.

2001 s10 ext cab 6.0 243 heads, ls2 cam, nnbs truck intake, 87mm tb, 4l60e, 241c, dana 44's front and rear, 4.30 gears 35" m/t Baja claws. My blazer tank is from a 99 model. I used the sending unit from my truck by shortening the spring loaded rods that guide the bucket.

Cost for the swap 36 gallon tank $150 extended range fuel pump $267 fuel tank swap labor $300 That makes a total of $717, in the event someone else wants to do one. I haven't ventured into Forscan yet, however there's some curious DTE readings going on after the swap. Immediately after the swap, I went to the gas station and filled up the …1st gen Blazers/Jimmys had either 13.2 or 20 tanks. I don't know the 2 or 4 door differences. 1 gen s10/Sonomas have either 13 or 20 gallon tanks. Either tank could be in short beds, long beds, regular cabs, ex cabs. ALL 2nd gen trucks have 18.5 gallon tanks.6.2K views 10 months ago. Today we continue our "How to LS Swap" series with getting our new gas tank in the car. This is part 1 of 2 for the fuel system in the series. There was a …Gas Tank options. Jump to Latest ... Blazer Gas Tank Swap/Build/How-To Hey guys. As I mentioned in my build thread, I was going to try my best making a semi-how-to ...

Re: 16 to 20 gallon tank swap? I'd put it on the passenger side. 20 gallons of gas is 120 pounds plus tank and brackets. Call it 150 pounds. Now let's say you weigh 180 pounds, and you usually drive the truck alone. Put the tank on the passenger side and that's 150 pounds on one side, 180 pounds on the other.

Gas Tank Swap. Jump to Latest Follow. 2K views 5 replies 3 participants last post by ShortyzKustomz Aug 29, 2009. SLVRFX Discussion starter. 11 posts · Joined 2009. #1 · Aug 27, 2009. Has any one swapped out a gas tanks for a larger one. I would like to put on one from a Silverado or something with about a 33 gal tank. Like.

You would defenitely be able to tell if it was bigger by poking your head under it because the 20 gallon tank is quite a bit longer. The bigger tank was actually an optional item as far as I know. 1985 S-10 Chevrolet Orange 2.8L w/5 speed, '93 grill, '89 blazer rear bumper, ZQ8s with 225/50 fronts and 245/50 rears. Like.For the return style manifold at least, parts are as follows for the picture explanation. RUS-640850 for the 3/8" feed line on the fuel rail to male -6AN, or RUS-640853 for black fitting instead of blue. RUS-650860 for the 5/16" return line on the fuel rail to male -6AN, or RUS-640863 for black.Let's check the charts of SWN -- and of surging natural gas future prices....SWN Employees of TheStreet are prohibited from trading individual securities. These recently downgr...looks like the metal tank that was on there, 18 gallons I believe. the fuel sending unit and lock ring, and on advance auto's website, I had 1999 GMC 4.8, and 2000 s10 4.3, in the vehicle search, and its the same lock ring, 32 gallon tank ring, but it fits. Save Share.I recently swapped my 4 cylinder for a 4.3. I am still working on finding a tank. I know that the vin 5 tank won't work the pump is clocked wrong. I'm getting different information on the tank. I have a straight cab and some sites it's different from the xtracab and others show them being the same. I'm sure one of you guys know.Feb 29, 2004 · hell we swapped my bed to another guys truck and his step side to my truck within 3 hours. its actually very simple. take off the rear bumper. take out the tail lights. remove the tail light harness from the bed. remove the ground strap from the frame that connects to the filler neck. remove filler neck from the gas tank along with the rubber ... These are the best sites to buy, sell and swap the gift cards that you don't want. By clicking "TRY IT", I agree to receive newsletters and promotions from Money and its partners. ...

Re: S10 Swap how to. After the fenders and hood are aligned and core support bolted down, I remove the hood/fenders to cut down the inner fenders. I generally cut along the lowest full wind line on the inner fender. Removing the bottom 3 or so inches. and then hold them in position to mark for the A-frame clearance.Chevrolet S10 LS Swap Systems. Availability. In Stock. The GM LS engine has quickly become the high-performance standard in the performance aftermarket. Holley and Hooker have partnered together to offer the most versatile and complete LS swap kits on the market so you can install the GM LS engine into your favorite chassis!Re: 1985 to 1987 Fuel tank & pump LS swap ... do myself or buy kit. I agree that the hydramat is a great idea, but can't believe how much it costs. The prices vary from about $150-$600, depending on the size you buy. And you still have to buy a high pressure fuel pump and sending unit to use with it.One of the more challenging aspects of an engine swap is engine mounting. Worry no more. The LS Engine Mount Plates are designed to eliminate a lot of the guesswork of component selection when installing a Chevy LS1/LS6 or Vortec 4.8/5.3/6.0L V8 engine into your 2WD truck. The LS engine mounts are available in two variations: the LS Mount Plate ...It took a little longer to get this done but here it is. Gas tank is in its final resting place. All the fittings I need to run the fuel lines have been orde...

I need a new gas tank for my LSx swap on a 1985 C/10 SWB. I can get this 1990 blazer tank. Is this a direct bolt-in on the pickup chassis? I know the fuel inlet will need to be …

Dec 9, 2002 · First of all, the swap of a 2.2 requires a lot of time and patience. To make this easier, I’m doing a fuel-injected engine to a fuel-injected engine. Meaning there’s no need for gas tank modifications. If you go from carbureted to EFI, or vice versa then you need a new Gas tank unit for the appropriate method. Ok, now lets start. 246 posts · Joined 2022. #1 · Sep 29, 2023 (Edited) Just thought I'd post about using the stock gas tank for an injected LS/Vortex swap for those wondering if it's usable. I believe some guys think you need to use a specialty fuel injection designed tank or possibly modify your tank to use an in tank pump and sender unit, or that it needs ...5.3 Fuel Pump in a Stock S10 Gas Tank LS Swap fuel system made easy. Wil's Workshop. 7.72K subscribers. Subscribed. 104. 9.4K views 2 years ago. Push Lock conversion complete, much easier...Beater '91 S10 :rant: Pimped out '03 Yukon. Air'd out 1992 Chevy S10 Ext. Cab; Slam ES bags, a couple GC 450 1/2" valves for each bag, 1/2 ID hydro' line and 10G of air to fill them, with a ViAir 550 to fill the tank. UNDER MAJOR CONSTRUCTION TOP SECRET. www.mothergoosecustoms.com.They are two different height pumps, the 20 gallon pump will not fit in the 13.2, trust me. I think I already said you can not swap pumps, but I guess technically you could swap the pump alone, the sender and other assembly will not fit. 1989 Chevrolet Blazer 3.4. 1989 Chevrolet Blazer 4.3 4x4. 1989 Chevrolet Blazer 4.3 Edelbrock equipped.If you tank is not full (bad sending unit), There is an anti-siphon ball in the filler neck, take the two hoses off and check to make sure it is not stuck. 2002 Dakota, QC 4x4, 4.7L HO Intake. 1997 S10 ZR2, Ext Cab, 5 Speed SOLD. How to test fuel pressure and leak down <---Diagnostic help. Shop Repair Manual <----Click to download.Re: S10 Swap how to. After the fenders and hood are aligned and core support bolted down, I remove the hood/fenders to cut down the inner fenders. I generally cut along the lowest full wind line on the inner fender. Removing the bottom 3 or so inches. and then hold them in position to mark for the A-frame clearance.First Gen In-Tank Fuel Pump Options. I've got a 1984 s10 extended cab, and the 2.8 just kicked the bucket. I'm weighing my options. I've been trying to work out how I'd run an in tank fuel pump if I decide to run the LS route. While there's a lot of really helpful info in the stickies, much of the info in them and returned in the search results ...

TV host Dave Welch shows just how easy it is to mount a Blazer/Suburban style tank under the bed of your 1963-1972 Chevy or GMC in this complete installation...

Tanks Inc. Blazer tank swap.

The headers are mandrel bent and TIG-welded. The LT’s factory flexplate is designed for use with the latest six- and eight-speed transmissions. If you are swapping a 4LXX-series transmission, then you need a new flexplate like the billet SFI 29.2 unit from TCI (part No. 399860). The Gen V crankshaft is an 8-bolt.The Gen-III LS swap is the hot ticket to add big power and reliability to your classic. But that late model power is going to require a dedicated LS swap fuel pump. The video below highlights the Speedway Motors electric fuel pump conversion that we chose as an EFI swap fuel pump for the 5.3 LS in our project ’68 C10.550. Originally Posted by STLWS6. Hi everybody did a 99+ 411 pcm swap in my 98 trans am and my fuel gauge does work. Pulled the pumps out put in a new sender unit that was doubled checked at the pcm pin 56 and was recording 18 ohms empty and 248 full with a ohm meter. I am pretty sure that its in the tune but do not know what to …looks like the metal tank that was on there, 18 gallons I believe. the fuel sending unit and lock ring, and on advance auto's website, I had 1999 GMC 4.8, and 2000 s10 4.3, in the vehicle search, and its the same lock ring, 32 gallon tank ring, but it fits. Save Share.Ground the gas tank terminal post of the tank sending unit using a jumper wire. If the dash gauge now reeds empty, the gas tank unit is defective. ... S10 Frame Swap on an Advanced Design Chevy Truck. Similar Posts. Classic Chevy Trucks. S10 Frame Swap on an Advanced Design Chevy Truck. By Jake Mayock May 12, 2018 …I got the Blazer fuel tank installed and all associated fab work done on the frame. Bed modifications still to comeFuel your LS swap or EFI conversion with an easy to install universal in-tank fuel pump module. This submersible fuel pump module features a billet aluminum top plate and has an adjustable tank depth from 5 to 16 inches. Includes a Walbro GSS340 fuel pump which has a 255 LPH flow rate and is for use with 40 to 70 psi of fuel pressure. The pump ...Universal Flush Mount Fuel Filler Kit. 5.0. (4) MSRP $59.99 set. Classic $53.99 set. VIEW DETAILS. Classic Industries offers a wide selection of Fuel Tank Hardware for your 1984 Chevrolet S10. Classic Industries offers 1984 Chevrolet S10 Mounting Hardware.Gas tank swap. Jump to Latest Follow ... S10 addiction: (7) S10s and one LUV. Save Share. Like. CharliesS10 Discussion starter 30 posts ...

Improving your fuel economy has many benefits including saving you money, here is how to get better gas mileage next time you fill up your tank. * Required Field Your Name: * Your ...Do you know how to host a book swap? It is a great way to trade in your books for new ones. Learn how to host a book swap at HowStuffWorks. Advertisement If you love the written wo...Re: S10 Swap how to. After the fenders and hood are aligned and core support bolted down, I remove the hood/fenders to cut down the inner fenders. I generally cut along the lowest full wind line on the inner fender. Removing the bottom 3 or so inches. and then hold them in position to mark for the A-frame clearance.Instagram:https://instagram. good movies on xfinity for freeroseau county sheriff departmentamherst new york police blotterdiscount tire morse crossing 559 posts · Joined 2011. #11 · Jun 15, 2014. Probably worth bringing up here that if you use the S10 Flex Fuel filter and regulator the 5/16 is the inlet and the 3/8 is the return, if you use the Corvette fuel filter and regulator they are opposite (i.e the 3/8 is the inlet, and the 5/16 is the return). Don't know why, but a search will turn ...The little plastic clips on all the fuel line disconnects break. No matter how gentle you are. There is a blue fitting on top of the tank that connects to the fuel pump. On the 26 gal tank this fitting is right next to the fuel pump. On the 32 gallon tank the fitting is all the way at the front of the tank. Need a longer hose. how much is britbox on xfinityfemale agents casting 2001 s10 ext cab 6.0 243 heads, ls2 cam, nnbs truck intake, 87mm tb, 4l60e, 241c, dana 44's front and rear, 4.30 gears 35" m/t Baja claws. My blazer tank is from a 99 model. I used the sending unit from my truck by shortening the spring loaded rods that guide the bucket. ncg kennesaw Tanks Inc. Blazer tank swap. Product Summary. 47-54 Chevy, EFI Conversion Fuel Tank Style, Aluminum. This complete EFI ready fuel tank kit makes it easy to mount a tank under the bed of your 1947 to 1953 Chevy pickup with an LS swap or EFI conversion. Includes a Walbro GSS340 in-tank fuel pump and bolt-in submersible fuel pump module for use with EFI systems at 40 to 70 ...